• EN54 Parts 2 & 4 042bc ¨ Local audible buzzer for event announcement. The Nano panel is designed to meet the requirements of ¨ Push buttons for essential controls and menu driven EN54-2: 1997 and EN54-4:1997. The panel can accommodate commands. • www.acornfiresecurity.com Installation instructions Master alarm 2 - Master alarm circuits Technical data circuits and operating at 24 volt nominal, Control panel fuses 200 mA maximum per circuit Standard Designed to EN54-2: 1997 MA1 - Fuse FS2 250mA AS MA2 - Fuse FS3 250mA AS Approval LPCB approved Both fuses are Ceramic type. • www.acornfiresecurity.com Nano System Power supply Controls at As for controls at Access level 1 Standard Designed to EN54-4: 1997 plus controls for: Access level 2 ¨ (Customer mode) Mains supply 230V 50Hz protected by: Cancel buzzer voltage and fuses FS3 Fuse - 3.15A (T) 250V ¨. Free download galileo reservation system. Galileo reservation system free download, BMS Business Music System 4.08, Crystal Audio Engine (Full System) 0.1b, Sound Cue System 10.8.1. Download Galileo for free. Galileo is a powerful project design software for the XV platform. That's how much we trust our unbeatable service. E2 shop system cracked. • Installation instructions Panel installation The Nano panel is supplied fully assembled, it is important to check the contents to ensure all the parts are supplied. Note the 2 x 12V 7Ah batteries are supplied in a separate pack. Parts in the Spares packages Quantity Fuse T3.15A H 250V 20mm x 5mm Ceramic. • www.acornfiresecurity.com Nano System How to mount the backbox and dedicated cable entry points & Unused knockouts that have been removed should not be left open. Knockout the required dedicated cable entry points from the back box. Use the correct method of knocking out the entry points, as illustrated below. • www.acornfiresecurity.com Installation instructions Flush Mounting the backbox The control panel may be flush mounted using a flush surround NANO-FLUSH. Gent Vigilon En54 ManualWireless Fire Detection Alarm Systems, Life Safety, Smoke and Fire Detection by Gent by Honeywell. Gent by Honeywell is synonymous with quality and innovation in the fire detection and alarm industry. This manual covers the Operating instructions and Log book, and is intended for use by the End User. The manual should be located in a secure but accessible position close. Cut out an aperture in the wall to allow the flush surround to be fitted, see diagram for dimension of the aperture. Using the fixing holes on the flush surround, secure it into the aperture side walls. • www.acornfiresecurity.com Nano System Cable termination on enclosure The wire length between the cable termination and point of connection must be as short as possible. Cable earth drain wire, where applicable, must be connected to the respective drain termination point. Softskin (Fire Tuf) CABLE TERMINATION Master Fire. • www.acornfiresecurity.com Installation instructions Mains supply & Ensure that the mains supply cable enters the panel through a dedicated cable entry, located adjacent to the mains terminal block and that is also segregated from loop wiring. ' These fire alarm system products are not designed to be powered from IT Power systems. Gent Vigilon En54-2 & 4 ManualAll mains powered equipment must be earthed. • www. Agilent chemstation software download. acornfiresecurity.com Nano System Terminals for external circuits on Main Control Board The Main Control Board (MCB) holds all the terminals for the connection of fire alarm loop circuit, master alarms, fire and fault relays, class change, evacuate input and repeat indicator panel. • www.acornfiresecurity.com Installation instructions Device loop circuit The device loop circuit can accept connection of addressable devices, up to 127 maximum. To maintain earth continuity on the loop, the loop cable screen must be continued through each system device, whether the earth is connected to a device or not. • www.acornfiresecurity.com Nano System Master alarm circuits Common Fault contacts There are two MASTER ALARM circuits that can accept the The control panel has a COMMON FAULT relay having voltage connection of conventional alarm sounders including the free contacts that can be used to signal external equipment. Gent En 54 Vigilon Operating Manual![]() The conventional Speech-Sounder-Strobe S products. • www.acornfiresecurity.com Installation instructions Fire Output contacts Repeat indicator panel The control panel has a FIRE OUTPUT relay having voltage free Up to four REPEAT INDICATOR PANELS can be connected contacts that can be used to switch plant equipment, such as lift directly to the fire panel to its RS485 Port. • www.acornfiresecurity.com Nano System External Evacuation input RS232 Port The EVACUATION INPUT function is activated on operation of The RS232 port of the fire panel can be configured to allow an external switch wired in the manner shown below. The switch connection of external printer. • www.acornfiresecurity.com Installation instructions Battery installation The batteries are fitted inside the backbox and connected up in the manner shown, however the final connection to power up the panel is made during system commissioning, which is done by the servicing organisation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
January 2019
Categories |